Collect air readings along workshop routes.Revisit anomalies for staff review.
Collect air readings along workshop, storage and shared-corridor routes, revisit anomalies and let staff review and respond.
Set areas, checkpoints, routes, time and frequency.
Present collected information, task states and alerts.
Review readings, images or live views and decide on action.
Where the service helps
Coordinate routes, content and staff around these tasks.
Fixed routes
Schedule by shift and area.
Priority points
Material storage, odor complaint locations and exhaust surroundings.
Anomaly revisit
Recheck threshold alerts for human review, marking and response.
Heatmaps and trend screens are illustrative, not certified test reports. Automatic source attribution, hazardous-gas certification and HVAC control are not established.
Service flow and ownership
Robots execute configured tasks; responsible staff retain verification and on-site response.
Set areas, checkpoints, routes, time and frequency.
Follow configured indoor routes and collect at checkpoints.
Present collected information, task states and alerts.
Review readings, images or live views and decide on action.
Mark the outcome and retain task, location, time and event records.
Confirm execution separately from human handover/review; assigned staff take over exceptions.
Roles
Robot
Patrol, collect and report site information.
Duty staff
Review conditions and contact responders.
Site and support staff
Respond and maintain equipment, routes and records.
Service modes
Select modes for the workflow; agree extensions separately.
Fixed routes
Schedule by shift and area.
Priority points
Material storage, odor complaint locations and exhaust surroundings.
Anomaly revisit
Recheck threshold alerts for human review, marking and response.
Heatmaps and trend screens are illustrative, not certified test reports. Automatic source attribution, hazardous-gas certification and HVAC control are not established.
Scenario fit
Collect air readings along workshop, storage and shared-corridor routes, revisit anomalies and let staff review and respond.
Fixed routes
Schedule by shift and area.
Priority points
Material storage, odor complaint locations and exhaust surroundings.
Anomaly revisit
Recheck threshold alerts for human review, marking and response.
Terminals and configuration
Document-based scope; confirm supplied model, options and site fit.
Sensors
Confirm temperature, humidity, PM2.5, PM10, TVOC and odor readings against fitted sensors; illustrative CO₂ does not make it standard on every unit.
Platform
Threshold alerts, trends, event records and optional data interfaces.
Coordination priorities
Assign suitable repeated routes to robots and compare results in the pilot.
Verify outcomes against task, destination and responsible role.
Use task states and exception records to adjust routes, schedules and configuration.
Routes and service points
Configure routes for the actual site; diagrams explain the workflow.
Workshop aisles
Associate readings with point and time.
Storage / odor points
Configure sampling and revisit rules.
Staff areas
Include accessible areas according to need.
Locations
- Workshop aisles
- Storage / odor points
- Staff areas
Diagrams explain the flow; survey actual passages, thresholds, access and stops.
Site readiness and operations
Confirm site, equipment and staffing; verify interfaces per project.
Human response
Staff review readings and the site, recording action and retest results.
Readiness
Confirm sensors, thresholds, routes, network and charging, with maintenance appropriate to fitted devices.
Commission configured interfaces, notifications and access; assign site contacts and staff fallback.
Document configuration and device checks
| Sensors | Confirm temperature, humidity, PM2.5, PM10, TVOC and odor readings against fitted sensors; illustrative CO₂ does not make it standard on every unit. |
|---|---|
| Platform | Threshold alerts, trends, event records and optional data interfaces. |
Document and current product versions may differ; confirm supplied specifications and project configuration.
Pilot and expansion
Pilot one robot, one fixed route and several time windows covering main aisles, storage, complaints and exhaust surroundings.
Sensors
Confirm temperature, humidity, PM2.5, PM10, TVOC and odor readings against fitted sensors; illustrative CO₂ does not make it standard on every unit.
Platform
Threshold alerts, trends, event records and optional data interfaces.
Suggested sizing assessment
Match full patrol cycles to measured checkpoint revisit intervalsUse site data including access, handover, waiting, charging and exceptions; travel speed alone does not establish capacity.
This is an assessment method; source recommendations/targets are not universal performance guarantees.
Sizing considerations
Task cycle
Measure request, execution, handover, return and charging time.
Site scope
Workshop aisles, Storage / odor points, Staff areas
Staff coordination
Allow for available receiving, reviewing and exception-response staff.
Source configurations/data refer to their stated scenario; confirm final sizing through site validation.
Suggested implementation
The following are project assessment and acceptance suggestions, subject to site confirmation.
Confirm scope
Site preparation
Configure and commission
When ready
Trial and acceptance
By project agreement
Suggested exception handling
The following are project assessment and acceptance suggestions, subject to site confirmation.
| Condition | Action | Ownership and records |
|---|---|---|
| Task cannot continue | Pause, wait or hand over to staff under site rules. | Managers record cause, owner and recovery conditions. |
| Handover/review incomplete | Contact the assigned staff; automatic task closure does not replace their confirmation. | Record the reason and follow-up. |
| Device/access exception | Follow support procedures and use staff service if required. | Support and site staff coordinate and validate recovery. |
Common questions
Where should the pilot start?
Pilot one robot, one fixed route and several time windows covering main aisles, storage, complaints and exhaust surroundings.
How do robots and staff share work?
Robot：Patrol, collect and report site information. Duty staff：Review conditions and contact responders. Site and support staff：Respond and maintain equipment, routes and records.
What needs separate confirmation?
Heatmaps and trend screens are illustrative, not certified test reports. Automatic source attribution, hazardous-gas certification and HVAC control are not established.
How are configuration and acceptance set?
Use source recommendations as a starting point, then confirm against site routes, supplied equipment and trial data. Suggested checks do not establish fixed performance or service guarantees.
Pilot preparation
Pilot one robot, one fixed route and several time windows covering main aisles, storage, complaints and exhaust surroundings.
| Item | Scope | Confirmation |
|---|---|---|
| Scope and points | Workshop aisles, Storage / odor points, Staff areas | Confirm accessible scope and responsible staff on site. |
| Routes and access | Maps, passages, doors/lifts, network and charging. | Commission cross-floor and controlled-door access as needed; diagrams do not replace site tests. |
| Handover and exceptions | Robot, Duty staff, Site and support staff | Agree notifications, staff takeover, records and review rules. |
Scope and points
Workshop aisles, Storage / odor points, Staff areas Confirm accessible scope and responsible staff on site.
Routes and access
Maps, passages, doors/lifts, network and charging. Commission cross-floor and controlled-door access as needed; diagrams do not replace site tests.
Handover and exceptions
Robot, Duty staff, Site and support staff Agree notifications, staff takeover, records and review rules.
Related equipment
Review product information and reconcile the document version with the supplied model/configuration.
View productRelated solutions
Choose a dedicated solution for each workflow.
Factory indoor security patrol
Robots patrol, collect and notify; the platform unifies records and enterprise staff decide and respond.
Explore Solution →Factory sample and quality-inspection transfer
Connect production, receiving, inspection, retesting and retained-sample storage with manual packaging, authorized handovers and task records.
Explore Solution →Production-line material and tool delivery
Transport standard materials, tools and empty containers through requests, preparation, loading, delivery, human checks and records.
Explore Solution →